Posts Tagged ‘design sponge’

diy project: sculptural paper orb lights

Tuesday, May 1st, 2012

I found this great diy project via Design Sponge. It is inexpensive, creative and the results are simply fabulous! I will be making my own this weekend, so excited! =)

Materials

  • 100–125  white standard-sized paper cupcake liners
  • 100–125  vertically striped petit fours papers
  • (1) 18–20″ white paper lantern
  • hot glue gun
  • 1 Hemma Cord from IKEA (for lighting) ($3.99)

Instructions

1. Assemble the lantern and place it top up in a wide, shallow bowl to act as a base.

2. Put a small dot of hot glue on the backside of a white cupcake liner. Starting about 1/2″ in from the wire ring at the top of the lantern, place the cupcake liner on the lantern and press until it is attached.

3. Continue around the ring, spacing the papers so that the circular bases are approximately 1″ apart, allowing the outer edges to merge and shape.

4. Apply the cupcake papers around the lantern in rings until you are 3/4 of the way down, and then flip the lantern over and gently place it back in the bowl, top side down.

5. Complete the underside, and fill in the bottom so that the papers cover the base opening.

6. Begin applying the petite fours papers, centering them inside each white paper. Three-quarters of the way up the lantern, flip it top side up. Complete the top side.

7. Go back through, gently manipulating the outer papers to the desired shape. I kept mine fairly organic.

8. Drop a light in, and voila!

  • Share/Bookmark

DIY: Wine Crate Display Cases

Monday, January 9th, 2012

Check out these unique DIY Wine Crate Display Cases! I was looking for an interesting / inexpensive  solution to display art and I found it at Design Sponge!  I love the rough look of the wooden boxes against the elegant print.  So unique!

Wine Crate Display Cases!

Here is what you will need to complete this project:
Metal ruler
Crate
Gift wrap or other fancy paper
Pencil
X-acto blade
Bone folder
Spray adhesive
Sawtooth hanger
Hammer
Small nails
Rubber bumpers
Hanging hardware

Wine Crate Display Cases!

First, use a metal ruler to measure the interiors of each crate to make sure you have enough fancy paper to line all of them. Next, draw out the measurements in pencil on the backside of the paper. In order to avoid any potential gaps along the interior edges, add a 1″ “allowance” as follows:

Long pieces: add 1″ to each of the three sides that border the interior of the box.
Short pieces: add 1″ allowance to the side that borders the back of the box.
Back piece: no allowance necessary

Using a straight edge and an X-acto blade, carefully cut out each piece of paper (five per box). Create fold lines by scoring along your pencil marks with a bone folder. Finally, miter each of the interior corners by cutting a 45 degree angle from the outside edge in, along the 1””allowance.

Now it’s time to glue. In a well-ventilated area, apply spray adhesive to the back sides of each of your long pieces. Carefully place them carefully inside the box, lining up the folded edges with the edges of the box and smoothing out any air bubbles that may appear in the paper. Next, spray and apply the short pieces. At this point, all four sides of the box will be lined, and the back will have a 1″ border all the way around it. The last step is to spray and apply the back piece to the box. Smooth out bubbles and let dry completely before proceeding to the next step.

Decide which direction you want to hang your boxes, and attach a sawtooth hanger along the top edge of each box using a hammer and small nails. Apply peel-and-stick rubber bumpers along the bottom corners of each box, to ensure that they hang straight against the wall.

Mark the position of each box on the wall with a pencil, and attach them using the appropriate hanging hardware for your wall.

Thank you Design Sponge for the inspiration!

  • Share/Bookmark